JetCat SPH5 Скачать руководство пользователя страница 43

Страница: 43 / 60

Explanation for Turbine Shut Down

In the run menu, state selection, are the following explanations for the last shut down
condition of the turbine.

Code Value

Explanation

1 R/C

Off

Throttle stick and throttle trim moved to the minimum position.

2 OverTemp

Turbine running over temperature. Exceeded high
temperature parameter and time out.

3 IgnTimOut

Turbine did not ignite within programmed time interval.

4 AccTimOut

Turbine achieved ignition, but did not accelerate within
programmed time interval.

5 Acc.Slow

Turbine achieved ignition, but acceleration was less than the
programmed value, during startup.

6 Over-RPM

Turbine exceeded the maximum RPM, by 5% and a delay of
0.5 seconds.

7 Low-RPM

Turbine running under the minimum RPM, by 10% and a
delay of 3 seconds. Usually triggered by a flame out.

8 BattryLow

Battery pack is dead. Cell voltage is < 1.0V.

10 LowTemp

EGT dropped below the minimum value. A dislodged EGT
sensor can trigger this shut down.

11 HiTempOff

EGT exceeded the maximum range (~950 °C).

12 GlowPlug!

Defective glow plug.

13 WatchDog

ECU processor was locked out usually from static discharge
or voltage spike in power supply.

14 FailSafe

Turbine was shut down from a failsafe timeout condition.

15 ManualOff

Turbine was shut off by using the GSU.

16 PowerFail

The power failed to the ECU when the turbine was running.
This will occur if the power was lost because of a defective
battery, connection or if the switch is turned off before the
engine is shut-down.

Note: If this state is displayed the Info, Min/Max and
Statistics menus retain information from the previous
run.

17 TempSensor

Fail

EGT sensor failed.

Note: This could happen only during startup.

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды