JetCat SPH5 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 60

background image

switch. This

should be programmed to give low, medium and high output pulses to one

channel and the Aux lead from the ECU should be plugged into that channel.

Set up the head speed as normal for R1 as above. Press and hold the LIMITS button
and press the SELECT MENU button until you get to TURBINE LIMITS.

Release the LIMITS button and then press the + button to step through the menu. Keep
pressing it until you get to the AUX CHANNEL FUNC menu

Press and hold CHANGE VALUE and press + repeatedly and the AUX CHANNEL
FUNC will eventually read RPM-SWITCH ON. Release the CHANGE VALUE button

Repeatedly press the + button until you get back to the SHAFT HI R0. When you press
it again you will see SHAFT HI R1 and again it will show SHAFT HI R2.

Turn on the transmitter and put the switch selected for the speed change control in
either the slow, medium or high speed position. By Using the CHANGE VALUE and the
+ and - buttons you can alter the values of the slow, medium and high rpms. You must
have the TX switch in the position of the speed you want to alter or the GSU will say
THIS VALUE CANNOT BE CHANGED

52

«
...
50
51
52
53
54
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: YOODA Страницы: 7

Бренд: Daihatsu Страницы: 294

Бренд: WÄRTSILÄ Страницы: 200

Vanguard 540000 Series

Бренд: Briggs & Stratton Страницы: 32

Бренд: Man Страницы: 90

X Trainer 300 2T 2015

Бренд: Beta Motorcycles Страницы: 117

Бренд: Yamaha Страницы: 30

Бренд: Toyama Страницы: 44

Throttling Governor Kerosene Stationary Engines

Бренд: Worthington Страницы: 33

EASY-KART 100cc

Бренд: IAME Страницы: 35

MotorLift RA20F

Бренд: Chamberlain Страницы: 24

Бренд: Chamberlain Страницы: 40

Бренд: GPOWER Страницы: 4

Бренд: MULTIPLEX modell Страницы: 6

Grove - Servo Max

Бренд: Seeed Страницы: 9

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды