JetCat SPH5 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

Pump start voltage is adjusted too low:

If the pump start voltage is adjusted too low, the pump may not start to turn (

Æ

the red

“pump running” LED is illuminated, but the pump is not turning). This can result in the
turbine, after ignition on propane, running an unusual long time and not picking up RPM.
If this time is too long (>10sec.), the ECU will terminate the start and show an Error
message “AccTimOut” or “Acc. Slow” (=acceleration too slow).

Pump start voltage is adjusted too high:

If the pump start voltage is adjusted too high, the turbine maybe supplied with too much
fuel during start up. This could result in heavy flames behind the turbine (

Æ

turbine

RPM too low compared to fuel being supplied).

21

«
...
19
20
21
22
23
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: J.A.P Страницы: 21

Бренд: HunterDouglas Страницы: 20

Бренд: 3W Страницы: 20

GSX-R 1300 Turbo

Бренд: RPE Страницы: 19

GARDEN SNOWBUSTER (160F)

Бренд: Texas Страницы: 33

Бренд: Marcato Страницы: 42

Enduro RR 350 EFI 2016

Бренд: Beta Страницы: 158

Бренд: cemp Страницы: 18

Бренд: Fagor Страницы: 174

Бренд: AE Страницы: 4

Бренд: Detroit Diesel Страницы: 83

Бренд: NANOTEC Страницы: 295

Бренд: O.S. engine Страницы: 17

MAX-61RX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Бренд: Stiga Страницы: 40

Бренд: Briggs & Stratton Страницы: 100

Бренд: Desert Aircraft Страницы: 20

Бренд: Waukesha Страницы: 140

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды