JetCat SPH5 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 60

background image

The RUN Menu

As soon as the ECU is switched on, the default run menu is displayed.

Before starting the engine, the default display appears like this. The first line displays
the temperature in degrees Celsius, glow plug bad icon (flashing), remote mode icon,
failsafe icon and RPM in thousands. The second line displays battery voltage, remaining
battery voltage icon and the “

OC:

” Off Condition.

21

0.0

6.9

OC:----

Failsafe icon

Not displayed if
signal is OK

RPM in
thousands.

1/M

Off Condition /
Current State.

Remote mode icon / GSU.

Not displayed if currently
operated from the transmitter.

Defective Glow plug
icon (flashing)

Not displayed if
Plug is OK

Battery voltage

Remaining battery
voltage icon.

Current Temp.

During the start sequence of the engine, the “

OC:

” will be over written with all the

different states during the start process until the engine is at idle (green LED is on). The
battery voltage will change to pump voltage as well.

When the engine is in the RUN State, the display will be as follows ->

610 0.0

0.6

0.0

RPM in
thousands.

1/M

Set RPM. This is the
RPM equivalent to
where the throttle stick
is currently positioned

Pump voltage

Remaining battery
voltage icon.

Current Temp.

The pump voltage display is useful to monitor the voltage under full power. If this value
begins to increase over time, it may be an indication that the fuel filter is clogging. Make
note of the maximum voltage at full power for future reference.

When the engine is shut-off, the display changes back to the pre-start version. The Off
Condition can then be check for why the engine was shut-off.

R/C Off

is the normal

state when the user stops the engine.

45

«
...
43
44
45
46
47
...
»

Содержание SPH5





























































Отзывы:

Нет отзывов

Похожие инструкции для SPH5

Бренд: Sachs Страницы: 75

Бренд: BAFANG Страницы: 5

Бренд: Yanmar Страницы: 224

Бренд: 3W Страницы: 20

Бренд: Mercedes-Benz Страницы: 940

Бренд: Saito Страницы: 4

Бренд: IEF Werner Страницы: 38

Бренд: B&S Страницы: 26

Бренд: Komatsu Utility Страницы: 32

BCS 7700 Series

Бренд: Honeywell Страницы: 6

Бренд: Honeywell Страницы: 10

Modutrol IV Motors Series 90

Бренд: Honeywell Страницы: 12

Modutrol IV M9164A 1013

Бренд: Honeywell Страницы: 16

Modutrol IV 41 Series

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 40

Modutrol IV 72 Series

Бренд: Honeywell Страницы: 12

Бренд: Honeywell Страницы: 12

Modutrol IV M9175D 1014

Бренд: Honeywell Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды