JetCat SPH5 Скачать руководство пользователя страница 57

Страница: 57 / 60

Reset the ECU to the factory default values.

NEW FOR ECU V4.9R and later!

After resetting, the display will prompt you if you want to “

learn R/C

”. Press the

◄

- key

for NO or the

►

+ key for YES. After teaching the R/C system, the ECU will

automatically calibrate the EGT sensor.

To reset all the user parameters back to the factory default, perform the following steps.

This will put the ECU back to the “before delivery state”. You will need to
recalibrate the EGT probe, re-Learn R/C and set the fuel pump voltage for startup.

Press and hold the

Select Menu

key on the GSU, then switch on the power.

Remark:

Instead of pressing the

Select Menu

key on the GSU, the little key on the LED board

can be use instead.

The three LED´s first show the following blinking sequence:

LED

Blink

Sequence

Standby/Man.

Yellow

{

Pump running

Red

{

Green

{

....

The Display of the GSU will also show the message:

Release key to:
- learn RC -

Keep the Select Menu key pressed during this blinking sequence. It takes up to 10
seconds!

Next the 3 LED´s are showing the following sequence:

LED

Blinking

sequence

Standby

Yellow

{

Pump running

Red

{

Green

{

....

The Display of the GSU will change to the message:

Release key to:
Calibrate Temp

Keep the Select Menu key pressed during this blinking sequence. It takes up to
another 10 seconds!

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды