JetCat SPH5 Скачать руководство пользователя страница 38

Страница: 38 / 60

attempts. If the turbine does not ignite, during a 30-second period of attempts, the
process is aborted and the green

LED will blink.

4. As soon as ignition occurs, the yellow

Standby

LED will illuminate and the starting

motor is re-engaged to accelerate the turbine. At approximately 5000 RPM, the fuel
pump switches on and the red

Pump running

LED illuminates.

5. Turbine speed will progressively increase until achieving stable speed. When the

turbine speed surpasses the idle RPM value, the starter motor disengages and the
yellow

Standby

LED goes out.

6. As the turbine approaches approximately 55,000 RPM, it will briefly stabilize, before

automatically decelerating to idle RPM.

7. When the turbine attains idle speed and the throttle stick is placed at idle position,

the green

LED will illuminate, indicating that thrust control is now handed over to

the pilot.

Manual startup without using the transmitter directly from the GSU

The former

Manual Mode

has been removed in the v4.0 ECU. Therefore, a new

Manual Control Mode

with the following features are included:

•

The turbine can be started directly from the GSU. While pressing down the

Manual

key, press the

Ignition

key to start.

•

While pressing down the

Ignition

key, press the

►

+ or

◄

- key to incrementally

increase or decrease the turbine’s RPM.

•

While pressing down the

Ignition

key, press the

Run

key to set the RPM directly

to idle.

•

While pressing down the

Ignition

key, press the

Min/Max

key to set the RPM

directly to maximum.

•

While pressing down the

Manual

key, press the

Ignition

key to stop the engine.

The engine control can be switched from

Manual Control Mode

over to

RC control

and back while the engine is running. While pressing down the

Ignition

key, press the

Select Menu

key to switch control.

Note:

Switching from

Manual Control Mode

RC control

is only possible if the

throttle stick is in the idle position and, if the AUX channel is used, it must be in the
center position. When switching from

RC control

Manual Control Mode

, the engine

will be set initially to idle.

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды