JetCat SPH5 Скачать руководство пользователя страница 48

Страница: 48 / 60

Last Off Cond

Last stored Off condition.

Last MaxTemp

Maximum temperature during the last run.

Last MinTemp

Minimum temperature during the last run.

Last AvgTemp

Average temperature during the last run.

Last MaxR AvgTmp

Average temperature during the last run at maximum RPM.

Last StartTemp

Maximum temperature during startup during the last run.

Last MaxRPM

Maximum RPM during the last run.

Last MinRPM

Minimum RPM during the last run.

Last AvgRPM

Average RPM during the last run.

Last MaxPump

Maximum pump voltage during the last run.

Last MinPump

Minimum pump voltage during the last run.

Last AvgPump

Average pump voltage during the last run.

Last FailSafeCnt

Number of failsafe conditions during the last flight.

Last FailSafeTim

Time in a failsafe condition.

The Statistic-Menu

Menu parameters are for informational purposes only and cannot be changed.

Value

Explanation

Totl Run-Time

Total turbine running time (excluding startups).

Runs-OK

Number of successful turbine runs, without errors.

Runs aborted

Number of turbine shut downs, caused by the ECU’s safety system.

Ignitions OK

Number of successful ignitions.

Ignitions failed

Number of failed ignitions.

Starts failed

Number of failed starts.

LoBatt Cut-Outs

The number of low battery shutoffs.

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды