JetCat SPH5 Скачать руководство пользователя страница 35

Страница: 35 / 60

Release

Select Menu

only after the three LED’s display the following blink

sequence:

LED

Blink

Sequence

Standby/Man.

Yellow

{

Pump running

Red

{

Green

{

....

The GSU display will simultaneously read:

Release key to:
- learn RC -

4. This procedure enables a system mode, whereby the control positions can be

learned by the ECU. When

Select Menu

is released, only the green

LED should

illuminate.

The GSU display will read:

“

Off

” position

Set Throttle
control channel
to minimum:

5. Now the ECU can memorize the positions of the throttle control channel. First, place

the throttle control channel to low. Next, press

Select Menu

or the LED I/O board

switch, again. This will store the R/C system’s pulse width for immediate shutdown of
the turbine. The green

LED will turn off and the red

Pump running

LED will

illuminate. This indicates that the shutdown data has been set correctly.

The GSU display will read:

Throttle channel “

Idle

” position

Throttle Trim to
maximum:

6. Advance the throttle control channel to the center position. Press

Select Menu

the LED I/O board switch again, to store the R/C system’s pulse width for the turbine
idle position. The red

Pump running

LED will turn off and the yellow

Standby

LED

will illuminate.

This indicates that the turbine idle data has been set correctly.

The GSU display will read:

Throttle channel “

Full Power

” position

Set Throttle to
maximum:

Содержание SPH5




























































Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды

JetCat SPH5, Инструкция по эксплуатации

Результаты поиска

Содержание SPH5

Отзывы:

Похожие инструкции для SPH5

Бренды по названию

Популярные бренды