Jenaer Antriebstechnik ECOSTEP 54 Скачать руководство пользователя страница 7

Страница: 7 / 48

Subject to change without notice!

User Manual ECOSTEP®54

About this manual

Th is user manual describes the stepper ampliﬁ er series ECOSTEP®54. It concerns all persons who install,

commission and operate ECOSTEP®54 drives.

Further information:

Programming: manual „Object Dictionary ECOVARIO® and ECOSTEP®“

Motor data: Data sheets series 17S and 23S (stepper motors).

Th is manual makes the following demands on qualiﬁ ed personnel:

Transport: Personnel trained in handling electrostatic sensitive devices

Installation: Electrotechnically qualiﬁ ed personnel who know the security directives of electrical enginee-

ring and automation

Setup/Commissioning: Qualiﬁ ed personnel with a broad knowlege of the ﬁ elds of electrical engineering,

automation and drives

Safety instructions

2.1

Symbols

Table 2.1: Symbols

Pictogram

Warning

Consequences

General warning about danger

Disregarding this warning may
lead to death or serious injuries.

Warning about dangerous electri-
cal voltages

Disregarding this warning may
lead to death or serious injuries.

Warning about hot surfaces

Disregarding this warning may
lead to burns to the skin.

Содержание ECOSTEP 54

















































Результаты поиска

Содержание ECOSTEP 54

Отзывы:

Jenaer Antriebstechnik ECOSTEP 54, Руководство пользователя, Страница: 7 / 48

Результаты поиска

Содержание ECOSTEP 54

Отзывы: