Jenaer Antriebstechnik ECOSTEP 54 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 48

Jenaer Antriebstechnik ECOSTEP 54 Скачать руководство пользователя страница 33

Subject to change without notice!

User Manual ECOSTEP®54

33

Fig. 7.9: Operation mode Profile Position Mode (F5)

Th e parameters are described in the following table.

Table 7.5: Parameters in Profile Position Mode for ECOSTEP54

Parameter

Description

target_position

Target position [inc]

min_position_limit

Negative software limit position [inc]

max_position_limit

Positive software limit position [inc]

position_window

Target window symmetrical around the target position [inc]

max_profile_velo

Limitation of the proﬁ le velocity [inc/64 s]

profile_velocity

Proﬁ le velocity [inc/64 s]

profile_accel

Proﬁ le acceleration [16 inc/s]

profile_decel

Proﬁ le deceleration [16 inc/s

2

]

quickstop decel

Deceleration with „Quick Stop“ [16 inc/s

2

]

motion_prof_type

Acceleration proﬁ le (0: linear acceleration characteristics)

position_dem_value Position setpoint (motion proﬁ le generator output) [inc]

position_act_value

Actual position (identical with position_dem_value) [inc]

Th e Proﬁ le Position Mode is controlled by means of 3 bits of the control word:

Table 7.6: Control word in Profile Position Mode for ECOSTEP54

Control word
(binary)

Description

xxxx0xxxx

The target position can be set without immediate positioning

Transition from
xx000xxx to
xx001xxx

The drive carries out an absolute positioning according to the
defaults in the menu „Proﬁ le Position Mode“.

Transition from
xx100xxx to
xx101xxx

The drive carries out a relative positioning according to the
defaults in the menu „Proﬁ le Position Mode“.

xx011xxx

New absolute target positions become eﬀ ective immediately

«
...
31
32
33
34
35
...
»

Содержание ECOSTEP 54

















































Отзывы:

Нет отзывов