Japan Radio Co. JLR-7600 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 184

background image

4-43

4.9.4.2

STEP2 Selecting a screen structure

The screen structures of each display screen include customized screens that can be set freely, special
screens that do not allow any setting, and graphic screens.
Select a screen structure.
When display structure selection is set to “OFF”, the display screen cannot be registered.
Customized screen

One screen can be segmented into screens 1 to 4. Up to four contents can be displayed
concurrently.

Special screen and graphic screen

Users cannot change the screen structure. Special contents for the model are displayed on the
screen.

The following screen structures can be selected.
1) SEGMENTATION1:

Full screen

2) SEGMENTATION2:

The screen is segmented into two sections.

3) SEGMENTATION3:

The screen is segmented into three sections.

4) SEGMENTATION4:

The screen is segmented into four sections.

5) SPECIAL:

Special GPS screen

6) GRAPICH:

Graphic screen

7) OFF:

The screen can not be registred.

                                                                                                                                          Customized screen

                                 Select a screen
                                                                        structure




                                                       Screen structure

Select a display from
DISPLAY1 to DISPLAY6

or automatic

Segmentation 1

Segmentation 2

Segmentation 3

Segmentation 4

Special

Graphic

«
...
83
84
85
86
87
...
»

Содержание JLR-7600

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JLR-7600

Бренд: Garmin Страницы: 4

Zumo 550 - Motorcycle GPS Receiver

Бренд: Garmin Страницы: 1

Бренд: Garmin Страницы: 8

Бренд: Garmin Страницы: 8

Бренд: Neoway Страницы: 41

Бренд: Magellan Страницы: 51

Бренд: G Sat Страницы: 28

Бренд: UniGuard Страницы: 14

Бренд: UniGuard Страницы: 14

GPSMAP 162 Sounder

Бренд: Garmin Страницы: 99

HawkEye 7200A-BB2327

Бренд: Blue Sky Network Страницы: 27

Бренд: Datatool Страницы: 6

Бренд: ViaMichelin Страницы: 100

Бренд: Symmetricom Страницы: 90

Бренд: Packard Bell Страницы: 54

Бренд: trig Страницы: 4

Бренд: Xroad Страницы: 98

Бренд: Odetics Telecom Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды