Japan Radio Co. JLR-7600 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 184

background image

4-24

4.5 Route

Planning



Routes can be created using the registered waypoints.



A maximum of 20 routes can be created with this unit, with each route having up to 50 waypoints.



Arrival circle radii, route widths, planned speed and distance calculation method can be set for each

route.

4.5.1 Displaying the Route List

The created routes can be displayed in the route list.
The total distance is displayed in the registered route number.
The required time cannot be calculated for routes for which no planned speed has been set.

Route List

1. Press

the

key to display the main menu.

2. Press

the

key to select "WPT/ROUTE" and "MAKE ROUTE/LIST," and press the

key.

3. Move the cursor to the route number you wish to display, and press the

key.

On the Route information screen, arrival circle radius, route width, planned speed, distance
calculation method (GC/RL) and route waypoints are displayed.

Route information screen

Procedure

Route Number

Up/Dowm
scroll

Total distance of the
registered route

«
...
64
65
66
67
68
...
»

Содержание JLR-7600

























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для JLR-7600

Бренд: CHYNA SEA VENTURES Страницы: 17

Бренд: Navman Страницы: 94

Бренд: Prestigio Страницы: 42

Etrex Legend - GPS Receiver

Бренд: Garmin Страницы: 76

Бренд: Seiwa Страницы: 5

Бренд: Blue Sky Network Страницы: 21

Бренд: Raymarine Страницы: 24

Бренд: Becker Страницы: 145

Бренд: Enfora Страницы: 48

Бренд: OzSpy Страницы: 15

Бренд: Astrium Страницы: 2

RSA-1500 RSA-1500L

Бренд: RoyalTek Страницы: 18

Бренд: RoyalTek Страницы: 22

REB-1722 Series

Бренд: RoyalTek Страницы: 24

Monarch Go-GPS BLE

Бренд: SEQUANS Страницы: 28

Бренд: Winnes Страницы: 7

Бренд: X-Trax Страницы: 6

Бренд: SYNERGY SYSTEMS Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды