Japan Radio Co. JLR-7600 Скачать руководство пользователя страница 54

Страница: 54 / 184

4-12

4.2.8 Selecting

items from the menus

This section shows the procedure for selecting items from the menus and determining the selection.

1. Press .

2. Move the cursor to a required item by using

and press

. The item is selected and a

submenu is opened to enable selection of details.

Menu

Submenu

3. Move the cursor to a required item by using

and press

. The cursor moves to the

setting value selection.

4. Select a setting value with

and press

. The setting value is confirmed.

5. To return to the previous item, press

Procedure

The selected item
is displayed in
reverse video.

Setting value
selection

Power must not be off for 10 seconds after setting. When not doing so, the setting value may
not be saved.

Supplement

Содержание JLR-7600

























































































































































































Результаты поиска

Содержание JLR-7600

Отзывы:

Похожие инструкции для JLR-7600

Бренды по названию

Популярные бренды

Japan Radio Co. JLR-7600, Инструкция по эксплуатации

Результаты поиска

Содержание JLR-7600

Отзывы:

Похожие инструкции для JLR-7600

Бренды по названию

Популярные бренды