Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 29

Страница: 29 / 200

MAINTENANCE 4

en-29

4.20 EFI DIAGNOSTIC CHECK ___________________________________________________

The electrical system is equipped with an OBD-II and

Diagmaster diagnostic connectors located near the

engine controller.
Plug an OBD-II reader into the matching connector, turn

ignition switch to the ON position (do not start engine),

and refer to the instructions included with the reader to

retrieve diagnostic codes.

Refer to the HR-9016 Technical Repair Manual for code

descriptions.

4.21 WHEEL MOUNTING PROCEDURE ____________________________________________

Mower Wheels

1. Remove dirt, grease, and oil from stud thread. Do not

lubricate threads.

2. Position wheel on hub and inspect to insure full

contact between mounting surface of wheel and hub

or brake drum.

3. Finger tighten all hardware, then torque hardware in

crisis-cross order. Always tighten nuts in the to p
position.

4. After recieving new uni t, or if tires were removed,

check and torque lug bolts daily until torque is

maintained.

Front Wheels.............95-105 ft. lb. (128-142 N.m).
Rear Wheels .............65-75 ft. lb. (88-102 N.m).

Caster Wheels

To extend bearing life check and adjust caster and gauge

wheels every year. Lubricate bearings every 100 hours

using NLGI Grade 2 grease.

1. Raise deck so wheels are off ground and can be

rotated freely by hand.

2. Check wheels for end play

(I)

. Wheels should rotate

freely with zero end play.

3. To eliminate end play, tighten inner nut

(G)

until

wheel just begins to bind then loosen it 1/4 turn.

Lock inner nut in position using outer nut

(H)

. Do not

allow inner nut to rotate while tightening outer nut.

4. Repeat step 2 and check for end play.

Figure 4H

WARNING

Make sure the mower is parked on a solid and level

surface. Never work on a mower that is supported

only by the jack. Always use jack stands.

If only the front or rear of the mower is raised, place

chocks in front of and behind the wheels that are not

raised.

CAUTION

Check and torque lug bolts daily for the first 100 hours

of operation.

HR021

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды