Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 200

background image

MAINTENANCE 4

en-21

4.4

ENGINE _________________________________________________________________

IMPORTANT:

A separate Engine Manual, prepared by

the engine manufacturer, is supplied with this
mower. Read the engine manual carefully until you
are familiar with the operation and maintenance of
the engine. Proper attention to the engine
manufacturer’s directions will assure maximum
service life of the engine. To order replacement
engine manuals contact the engine manufacturer.

The proper break-in of a ne w engine can make a

considerable difference to the performance and life of the

engine.

During the break-in period, Jacobsen recommends the

following:

1. During the first 50 hours of operation, a new eng ine

should be allowed to reach an operating temperature

of at least 140°F (60°C) prior to operation at full load.

2. Check the engine oil level twice daily during the first

50 hours of operation. Higher than normal oil

consumption is not uncommon during the i nitial

break-in period.

3. Change engine oil and oil filter element after first 50

hours of operation.

4. Check and adjust fan and alternator belts.
5. Refer to

Section 5

and Engine Manual for specific

maintenance intervals and procedures.

6. Always allow the engine to be properly warmed up

before operating in both cold and warm seasons.

Warm up the engine at approximately half throttle

without load. Failure to properly warm up the engine

can shorten engine life.

If the injection pump, injectors, or the fuel system require

service, contact an authorized Jacobsen Dealer.

Note: The mower is designed to operate and cut most
efficiently at the preset governor setting. Do not change
the engine governor settings or overspeed the engine.

4.5

ENGINE OIL ______________________________________________________________

Check the engine oil at the start of each day, before

starting the engine. If the oil level is low, remove oil filler

cap and add oil as required up to MAX mark on dipstick.

Perform initial oil change after first 25 hours of operation

and every 250 hours thereafter. See Engine Manual.

Use engine oil with API classification CD-II, CE, CF-4.

See Engine Manual for complete specifications.

Figure 4D

4.6

MUFFLER AND EXHAUST ___________________________________________________

To protect from carbon monoxide poisoning, inspect the

complete exhaust system regularly and always replace a

defective muffler. If you notice a change in th e color or

sound of the exhaust, stop the engine immediately.

Identify the problem, and have the system repaired.

Torque all exhaust manifold hardware evenly. Tighten or

replace exhaust clamps.

S

AE 15W-40

+45˚C
+113˚F

- 20˚C
- 4˚F

HR005

WARNING

Exhaust fumes contain carbon monoxide that is toxic

and can be fatal when inhaled.

NEVER

operate an engine without proper ventilation.

!

«
...
19
20
21
22
23
...
»

Содержание HR 9016 Turbo 70538









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HR 9016 Turbo 70538

Бренд: Yard force Страницы: 53

Бренд: MasterCraft Страницы: 24

Бренд: Rally Страницы: 19

Бренд: jobmate Страницы: 19

Бренд: Redexim Страницы: 12

Бренд: Worldlawn Страницы: 16

Бренд: McCulloch Страницы: 44

Бренд: Scag Power Equipment Страницы: 38

Eco Wheeler GM 464.2 R

Бренд: Garten Meister Страницы: 94

Бренд: Worksaver Страницы: 40

Бренд: Sabo Страницы: 100

Бренд: Toro Страницы: 44

Бренд: Bad Boy Страницы: 48

Бренд: Worx Страницы: 44

Бренд: Scag Power Equipment Страницы: 23

TURF TIGER STT61V-29KB-DF

Бренд: Scag Power Equipment Страницы: 72

Бренд: Scag Power Equipment Страницы: 47

Бренд: Scag Power Equipment Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды