Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 10

Страница: 10 / 200

3 ADJUSTMENTS

en-10

ADJUSTMENTS

3.1 GENERAL ________________________________________________________________

1. Adjustments and maintenance should always be

performed by a qualified technician. If proper

adjustment cannot be mad e, contact an au thorized

Jacobsen Dealer.

2. Replace, do not adjust, worn or damaged

components.

3. Do not wear jewelry or loose fitting clothing when

making adjustments or repairs.

4. Do not change governor settings or overspeed the

engine.

3.2

LEVELING DECKS _________________________________________________________

If the decks or casters have been removed for service or

cutting height appears uneven, it may be nec essary to

level decks.

Adjust casters so cutting heights of outer

blades are within 1/8 in. (3 mm) of each other

1. Position mower and decks on a hard, flat, level

surface. Position blades parallel to mower as shown.

2. Check that air pressure in all caster tires is adjusted

equally.

3. Set desired cutting height of deck using the 1/2 in.

(13 mm) spacers

(E)

provided. See

Section 3.5

4. Measure the height from the ground surface to the

front edge

(B)

of th e two o uter blades for the wing

decks and the center section of the fr ont deck.

Position the 1/8 in. (3 mm) leveling washers

(C)

above or below caster pivot as needed to obtain an

even cutting height across decks. Keep the 1/16 in.

(1.5 mm) thrust washers

(D)

positioned as shown,

one above and one below caster pivot.

Figure 3A

WARNING

To prevent injury, lower implements to the ground,

disengage all drives, engage parking brake, stop

engine, and remove key from ignition switch before

making any adjustments or performing maintenance.

Make sure the mower is parked on a solid and level

surface. Never work on a mow er that is supported

only by the jack. Always use jack stands.

If only the front or rear of the mower is raised, place

chocks in front of and behind the wheels that are not

raised.

CAUTION

Be careful to prevent entrapment of the hands and

fingers between moving and fixed components of the

machine.

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды