Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 200

background image

3 ADJUSTMENTS

en-12

3.5

CUTTING HEIGHT _________________________________________________________

Cutting height for decks can be adjusted from 1 to 5-1/2

in. (25-125 mm) in 1/2 in. (13 mm) increments. Actual

cutting height may vary somewhat from the heights given

depending on turf conditions and other factors.

Note

:

When cutting undulating areas, lower cutting

heights may cause scalping. Adjust height accordingly to
prevent turf damage.

1. Park the mower on a flat, level surface. Raise the

decks until the caster wheels are raised off the

ground enough so caster wheels can be removed

from deck. Place blocks under decks so they are

supported on all sides.

To remove inside front caster from side decks, raise

the decks to their full upright position and lock in the

transport position.

2.

Figure 3E

shows the height adjustment decal for

the casters.
Column 1 - Height of cut

Column 2 - Mount Location

Column 3 - Arrangement of spacers

Adjust spacers in quantity listed. Store extra spacers

on top of spindle. If necessary, reposition wheel

mount in holes indicated for height of cut.

IMPORTANT: Do not reposition the thin thrust
washers (1/16 in.) and leveling washers (1/8 in.) on
the spindle. These washers should remain in the
same position and quantity they were originally
installed. They need only be repositioned if needed
to level new casters or decks, Section 3.2.

3. To adjust rear gauge wheels on fr ont deck, refer to

Figure 3F. Raise front deck approximately 12 in.

and support underneath with blocks. Lower deck so

it is completely resting on blocks

4. Remove pin from rear gauge wheel yoke and

reposition in bracket for desired height of cut. When

setting cutting height at 5-1/2 in., gauge wheel must

be repositioned in arm. Follow wheel mounting

instructions on decal,

Figure 3F

.

Figure 3E

Figure 3F

Tire pressure

Check air pressure in caster tires, while tires are cool.

Maintain air pressure between 20-25 psi (1.38-1.73 BAR)

to improve accuracy of cutting height.

Note

:

It is important to keep inflation pressures on all

caster and gauge tires equal, within the range specified,
to ensure an accurate, level cut.

WARNING

To prevent serious injury, lower deck until it is

resting completely on the su pports. This will

prevent it from accidentally lowering while making

adjustments. Disengage all drives, engage

parking brake, stop engine, and remove ignition

key.

!

Upper

Mount

Lower

Spacers
Under
Mount

Middle

Thrust
Washer &
Leveling
Washer

Never reposition the thrust washer(s) (1/16" thick)
and leveling washer(s) (1/8" thick)
when setting cut height

Cut

Mount

No. of Spacers

Height

Location

Under Mount

1 1/2

Lower

1

2

Lower

2

2 1/2

Lower

3

2 1/2

Middle

0

3

Middle

1

3 1/2

Middle

2

4

Middle

3

4

Upper

0

4 1/2

Upper

1

5

Upper

2

5 1/2

Upper

3

B

C D E

A

F

R

1

2

3 4

5

6

7

8

Arm

Bracket

Wheel
Mounting

Cut

Bracket

Arm

Wheel

Height

Hole

Hole

Mounting

1

3

A

F

1 1/2

1

B

F

2

2

C

F

2 1/2

3

D

F

3

4

E

F

3 1/2

5

B

F

4

6

C

F

4 1/2

7

D

F

5

8

E

F

5 1/2

8

E

R

Wheel Mounting Instruction
1 While rotating wheel, tighten

nut until wheel is difficult to
rotate.

2 Loosen nut 1/4 turn or just

until wheel rotates freely.

3 lock nut into place using

second nut. Do not allow
first nut to rotate when
tightening second nut securely.

4 Rotate wheel to check for

free rotation with zero end
play.

Gauge Wheel Adjustment for Front Deck

«
...
10
11
12
13
14
...
»

Содержание HR 9016 Turbo 70538









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HR 9016 Turbo 70538

Бренд: Troy-Bilt Страницы: 23

Бренд: Dixon Страницы: 13

Бренд: MTD Страницы: 47

Бренд: Kubota Страницы: 45

Бренд: Yardworks Страницы: 40

Бренд: Yard-Man Страницы: 8

Бренд: Yard-Man Страницы: 16

Бренд: Yard Machines Страницы: 12

Бренд: Yard Machines Страницы: 24

Бренд: Yard force Страницы: 50

Бренд: Yard force Страницы: 76

Бренд: Yard force Страницы: 98

Бренд: Wolf Garten Страницы: 34

Бренд: Wolf Garten Страницы: 30

Бренд: Snapper Страницы: 15

Бренд: Snapper Страницы: 24

Бренд: Snapper Страницы: 12

Бренд: Snapper Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды