Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 30

Страница: 30 / 200

4 MAINTENANCE

en-30

4.22 ROLLOVER PROTECTION STRUCTURE (ROPS) ________________________________

A Rollover Protection System (ROPS) designed for this

mower is available as an op tional accessory. If yo ur

mower is equipped with this device, inspect it periodically

and follow operating procedures described in Safety and
Operation Manual

1. The seat, the seat belt, mounting hardware, and any

accessories within the ROPS, should be i nspected

regularly, and all damaged parts replaced

immediately.

2. Once the ROPS has been subjected to any form of

impact it should be replaced.

3. Check and retorque all hardware. All replacement

components used for the ROPS must be as

specified in the Jacobsen Parts List.

4.23 STORAGE________________________________________________________________

General

1. Wash the mower thoroughly and lubricate. Repair

and paint damaged or exposed metal.

2. Inspect the mower, tighten all hardware, replace

worn or damaged components.

3. Drain and refill radiator.
4. Clean the tires thoroughly and store the mower so

the load is off the tires. If mower is not on jack

stands, check tires at regular intervals and reinflate

as necessary.

5. Keep the machine and all its accessories clean, dry

and protected from the elements during storage.

Never store equipment near an open flame or spark

which could ignite fuel or fuel vapors.

Battery

1. Remove, clean, and store battery in upright position

in a cool, dry place.

2. Check and r echarge battery every 60 to 90 da ys

while in storage.

3. Store batteries in a cool, dry place. To reduce the

self discharge rate, room temperature should not be

above 80°F (27°C) or fall below 20°F (-7°C) to

prevent electrolyte from freezing.

Engine

1. While the en gine is warm, remove drain plug, drain

the oil from the crankcase, and change oil filter.

Install drain plug and refill with fresh oil. Torque drain

plug to 22 ft. lb. (30 Nm).

2. Clean exterior of engine. Paint exposed metal or

apply a light coat of rust preventative oil.

3. Add a fu el conditioner or biocide to p revent gelling

or bacterial growth in fuel. See your local fuel

supplier.

Cutting Units

1. Wash the cutting units thoroughly, then repair and

paint any damaged or exposed metal.

2. Lubricate all fittings and friction points.
3. Apply a li ght coat of rust preventative oil to the

sharpened edges of the blades.

After Storage

1. Check and reinstall battery.
2. Check or service fuel filter and air cleaner.
3. Check the radiator coolant level.
4. Check oil level in the engine crankcase and

hydraulic system.

5. Fill the fuel tank with fresh fuel. Bleed the fuel

system.

6. Make certain that the tires are properly inflated.
7. Remove all oil from the deck blades. Readjust

cutting height.

8. Start and operate the engine at 1/2 throttle. Allow

enough time for the engine to become properly
warmed and lubricated.

CAUTION

Do not loosen or remove bolts, do not weld, drill, modify,

bend, or straighten a damaged structure.

WARNING

Never operate the engine without proper ventilation.

Exhaust fumes can be fatal when inhaled.

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды