Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 23

Страница: 23 / 200

MAINTENANCE 4

en-23

4.9

FUEL SYSTEM ____________________________________________________________

Refer to Section 5 for specific maintenance intervals.

See Engine Manual for detailed procedures.

Before replacing any filter, thoroughly clean the filter

housing and the area around the filter. Dirt must not be

allowed to enter into fuel system.

Bleed the fuel system after the fuel filter and lines have

been removed, or the fuel tank has become empty.

To change fuel filter

1. Close fuel valve on tank, then remove and discard

the existing filter.

2. Apply a l ight coat of oi l to the gasket and hand

tighten new filter.

3. Fill fuel tank. Open fuel valve on tank and bleed the

filter. See Engine Manual. Clean any spilled fuel

immediately.

4.10 BATTERY ________________________________________________________________

Make absolutely certain the ignition switch is “OFF” and
the key has been removed before servicing the battery.

Tighten cables securely to battery terminals and apply a

light coat of silicone dielectric grease to terminals and

cable ends to pr event corrosion. Keep vent caps and

terminal covers in place

Keep the cable ends, battery, and battery posts clean.

Verify battery polarity before connecting or disconnecting

the battery cables.

1. When installing the battery, always assemble the

RED, positive (+) battery cable first and the ground,

BLACK, negative (-) cable last.

2. When removing the battery, always remove the

ground, BLACK, negative (-) cable first and the

RED, positive (+) cable last.

3. Make sure battery is properly installed and secured

to the battery tray.

4.11 JUMP STARTING __________________________________________________________

Before attempting to “jump start” the mowe r, check the

condition of the discharged battery.

Section 4.10

When connecting jumper cables:

1. Stop the engine on vehicle with good battery.
2. Connect RED jumper cable to the positive (+)

terminal on th e good battery and to th e positive (+)

terminal on the “discharged” battery.

3. Connect the BLACK jumper cable from the negative

(-) terminal on the good battery to the

frame

mower with discharged battery.

After cables have been connected, start the engine on

the vehicle with the good battery then start the mower.

CAUTION

Always use insulated tools, wear protective glasses or

goggles, and protective clothing when working with

batteries. You must read and obey

all battery

manufacturer’s instructions

WARNING

Battery posts, terminals, and related accessories

contain lead and lead compounds, chemicals known

to the S tate of Ca lifornia to cause cancer and

reproductive harm.

Wash your hands after

handling.

WARNING

Batteries generate explosive hydrogen gas. To reduce

the chance of an explosion, avoid creating sparks

near battery. Always connect the negative jumper

cable to the fr ame of the mower with the discharged

battery, away from the battery.

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды