Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 16

Страница: 16 / 200

3 ADJUSTMENTS

en-16

3.11 PARKING BRAKE _________________________________________________________

1. Check linkage and pi vots to ens ure they are

operating smoothly. Inspect parking brake and

steering assist cables.

2. Park the m ower on a 30 % slope (16.7°) near the

bottom of the hill, with the front of the mower facing

downhill. Engage the parking brake and stop the

engine.

a. The mower should stay on the hill without

creeping.

b. If the brakes do not hold, start the engine,

disengage the brake, and drive to the bottom of

the hill.

3. With parking brake disengaged, turn adjusting knob

in a clockwise direction, applying and releasing

brake every quarter turn, until a defi nite “snap over

center” action is achieved.

4. Repeat the test on the hill if required.

Note:

Over adjustment causes hard lever action, but

does not increase brake efficiency.

3.12 TRACTION PEDAL _________________________________________________________

The traction pedal must be adjusted so the pump is at full

stroke when the pedal is fully depressed in the forward

position.

1. Make sure return arm

(K-Figure 3H)

on pump is

adjusted to neutral,

Section 3.6

2. Push traction pedal forward

(I)

until it to uches floor

panel and hold in this position.

3. Adjust turn buckle

(J)

until you feel the return arm

hit the internal stop in pump. Backoff rod 2-3 turns

from this position. This ensures that th e traction

pedal bottoms out before the return arm.

Figure 3L

3.13 STEERING TOE-IN _________________________________________________________

1. Turn wheels to straight ahead position.
2. Loosen jam nuts

(M)

on both ends of tie rod

(N)

3. Turn tie rod

(N)

to provide proper toe-in. Toe-in must

not exceed

+ 1/4 in. (6.3 mm). Tighten jam nuts

(M)

Figure 3M

CAUTION

DO NOT

disengage the brakes with the engine off.

HR019

X + 5/32" 3/32"

(4 mm 2.3 mm)

X +

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды