Jacobsen HR 9016 Turbo 70538 Скачать руководство пользователя страница 31

Страница: 31 / 200

TROUBLESHOOTING 5

en-31

TROUBLESHOOTING

5.1 GENERAL ________________________________________________________________

The troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed

information regarding the hydraulic and electrical systems contact your area Jacobsen Dealer.

Symptoms

Possible Causes

Action

Engine will not
start.

1. Parking brake disengaged

or power take-off switch

ON.

1. Check Interlock System and start-up procedure.

2. Glow plug has not timed

out.

2. Reset ignition switch and allow glow plug to time out

before cranking engine.

3. Battery low on charge or

defective.

3. Inspect condition of battery and battery connections.

4. Fuel tank empty or dirty.

4. Fill with fresh fuel. Change fuel filter. Bleed fuel lines.

5. Fuse blown.

5. Replace fuse.

6. Relay(s) defective.

6. Test and replace relay.

7. Traction pedal not in

Neutral.

7. Check position of pedal. Adjust Linkage.

8. Neutral switch on drive

pump not working.

8. Test, adjust, or replace switch.

9. Forward sensing switch on

drive pump not working.

9. Test, adjust, or replace switch.

Engine hard to
start or runs
poorly.

1. Fuel level low, fuel or fuel

filter dirty.

1. Fill with fresh fuel. Change fuel filter. Bleed fuel lines.

2. Air cleaner dirty.

2. Inspect and replace air filter.

3. Injectors, fuel pump.

3. Consult engine manual.

4. Engine problem.

4. Consult engine manual.

Engine stops.

1. Fuel tank empty.

1. Fill with fresh fuel and bleed fuel lines.

2. Interlocks not set before

leaving operator’s seat.

2. Engage parking brake and set power take-off switch to

OFF.

Engine
overheating.

1. Coolant level low.

1. Inspect and add coolant.

2. Air intake restricted.

2. Clean air intake at radiator.

3. Water pump belt broken or

loose.

3. Tighten or replace belt. See engine manual.

Battery not
holding charge.

1. Loose or corroded battery

terminals.

1. Inspect and clean terminals.

Battery light on.

2. Low electrolyte.

2. Refill to correct level.

3. Alternator belt loose or

broken.

3. Tighten or replace belt. See engine manual.

4. Charging system defective. 4. See engine manual.

Cutting units not
cutting evenly.

1. Cutting heights not set

evenly.

1. Check that decks are level. Check and adjust cutting height.

2. Engine speed too low.

2. Check engine speed with throttle in its fast position.

3. Mow speed not adjusted for

turf conditions.

3. Adjust mow speed for best cut.

4. Air pressure in caster tires

not adjusted correctly.

4. Check tires and adjust to correct pressure.

Содержание HR 9016 Turbo 70538









































































































































































































Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды

Jacobsen HR 9016 Turbo 70538, Руководство по запасным частям и обслуживанию

Результаты поиска

Содержание HR 9016 Turbo 70538

Отзывы:

Похожие инструкции для HR 9016 Turbo 70538

Бренды по названию

Популярные бренды