ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 98 / 178

122

136

112A

382

6.4.15.5 Disassemble the power end (XLT-i and i17 with duplex bearings)

Remove the bearing frame to frame foot (241) using the frame-foot bolts (370F).

228A

241

370F

370D

423

134

370C

Remove the clamp screws (370C) and back off the jam nuts (423).

Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame
(228A).

Remove the shaft assembly from the bearing frame (228A).

Remove the jack screws (370D) and the nuts (423).

Remove the bearing housing O-ring (496) and the inboard bearing (168A).

122

168A

248A

112A

136

382

253B

Remove the bolts (371C), the end cover (109A), and the gasket (360C).

If necessary, remove the outboard labyrinth oil seal (332A) from the end cover (109A) and remove
the O-rings (497F and 497G).
Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, or they are sold separately.

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды