ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 56 / 178

WARNING:

The coupling guard used in an ATEX classified environment must be constructed from a

spark resistant material.

Required parts:

Item Description

End plate, drive end

End plate, pump end

Guard half, 2 required

3/8-16 nut, 3 required

3/8 in. washer

3/8-16 x 2 in. hex head bolt, 3 re-
quired

Figure 34: Required parts

De-energize the motor, place the motor in a locked-out position, and place a caution tag at the start-
er that indicates the disconnect.

Put the pump-side end plate in place.
If the pump-side end plate is already in place, make any necessary coupling adjustments and then
proceed to the next step.

If the pump size is...

Then...

STi, MTi, LTi

Align the pump-side end plate to the bearing frame. You do not need to
adjust the impeller.

XLT-i

Align the end plate on the pump side to the bearing housing so that you
meet these conditions:

The large slots on the end plate do not touch the bearing housing
tap bolts.

The small slots align with the impeller adjusting bolts.

Fasten the end plate to the bearing housing using the jam nuts on the im-
peller adjusting bolts.

Check the impeller clearance. Refer to the impeller clearance table for the
correct impeller clearance.

5.6 Couple the pump and driver

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды