ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 31 / 178

background image

1

2

3

4

5

6

Item Description

1.

Driver's mounting pads

2.

Machinist's levels

3.

Foundation bolts

4.

Jackscrews

5.

Grout hole

6.

Pump's mounting pads

Figure 20: Level pump mounting pads

6.

Hand-tighten the nuts for the foundation bolts.

7.

Check that the driver's mounting pads are level and adjust the jackscrews and the foundation bolts
if necessary.

The correct level measurement is a maximum of 0.167 mm/m | 0.002 in./ft .

4.2.4 Install the baseplate using spring mounting

NOTICE:

The spring-mounted baseplate is designed only to support piping loads from thermal expan-
sion. Ensure that the suction and discharge piping are supported individually. Failure to do so
may result in equipment damage.

The foundation pads are not provided with the baseplate. Make sure that the foundation pads are 316
stainless-steel plates, which have a 16-20 micro-inch surface finish.

Before you start this procedure, make sure that the foundation pads are correctly installed on the founda-
tion/floor (see the manufacturer's instructions).

1.

Put the baseplate on a support above the foundation/floor.
Make sure that there is enough space between the baseplate and the foundation/floor in order to
install the spring assemblies.

2.

Install the lower part of the spring assembly:

a) Screw the lower jam nut onto the spring stud.

b) Screw the lower adjusting nut onto the spring-stud, on top of the jam nut.

c)

Set the lower adjusting nut to the correct height.

The correct height depends on the required distance between the foundation/floor and the base-
plate.

d) Put a washer, a follower, a spring, and one more follower onto the lower adjusting nut.

3.

Install the spring assembly on the baseplate:

a) Insert the spring assembly into the baseplate's anchorage hole from below.

b) Put a follower, a spring, another follower, and a washer onto the spring stud.

c)

Fasten the spring assembly with the upper adjusting nut by hand.

4.2 Baseplate-mounting procedures

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

29

«
...
29
30
31
32
33
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: Danfoss Страницы: 72

Бренд: Danfoss Страницы: 91

DHP-H Varius Pro+

Бренд: Danfoss Страницы: 12

Бренд: EasyPro Страницы: 8

Бренд: Jandy Страницы: 16

Бренд: wallas Страницы: 109

TURBOPOWER 1000 P 225A-TPL

Бренд: PVI Industries Страницы: 1

Бренд: Dupla MARIN Страницы: 28

ARO PP10A Series

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Rinnai Страницы: 18

Бренд: Bryant Страницы: 4

Бренд: Ribitech Страницы: 24

Бренд: TOHATSU Страницы: 87

Бренд: Ingersoll-Rand Страницы: 12

Бренд: A.O. Smith Страницы: 43

Бренд: Durapac Страницы: 11

Бренд: KNF Страницы: 88

Бренд: Pentair Jung Pumpen Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды