ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 96 / 178

NOTICE:

Do not reuse bearings if removed from shaft. Doing so may result in equipment damage. Re-
place the bearings before reassembly.

11. Remove the outboard labyrinth oil seal (332A) from the bearing housing (134).

12. Remove the O-rings (497F and 497G) if it is necessary.

Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, and they are sold separately.

134

497G

332A

497F

Figure 81: O-ring removal

6.4.15.4 Disassemble the power end (XLT-i and i17)

Remove the bearing frame from the frame foot (241) using the frame-foot bolts (370F).

228A

241

370F

370D

423

134

370C

Remove the clamp screws (370C) and back off the jam nuts (423).

Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame
(228A).

Remove the shaft assembly from the bearing frame (228A).

Remove the jack screws (370D), the nuts (423), and the bearing housing O-ring.

Remove the inboard bearing (168A).

6.4 Disassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды