ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 113 / 178

background image

168

361A

122

112

382

136

Figure 98: Inboard bearing reassembly

9.

Prepare the shaft for assembly as follows (see the illustration):

a) Install a new O-ring (496).

b) Coat the outside of the outboard bearing (112A) with oil.

c)

Coat the bore of the bearing housing (134) with oil.

d) Put the bearing housing (134) onto the shaft.

Do not use force.

e) Insert the bearing-retaining ring (361A) into the bore groove of the bearing housing (134).

NOTICE:

Ensure that the space between the ends of the retaining ring are located in the oil return
groove. Failure to do so will cause oil-flow obstruction and result in equipment damage.

Make sure that the shaft rotates freely.

f)

Install the outboard labyrinth oil-seal (332A) into the bearing housing (134).

Place the drain slots of the oil seal at the bottom position (6 o’clock).

Make sure that the edges of the keyway are free from burrs. To protect the O-ring, cover the keyway
lengthwise with a piece of electrical tape before you install the oil seal.

332A

134

112

361A

168A

496

Figure 99: Outboard labyrinth oil-seal reassembly

10. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.

b) Coat all the internal surfaces of the bearing frame (228) with oil.

c)

Install the shaft assembly into the bearing frame (228).

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

111

«
...
111
112
113
114
115
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: A.O. Smith Страницы: 20

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 24

Бренд: A.O. Smith Страницы: 6

Бренд: A.O. Smith Страницы: 2

Бренд: A.O. Smith Страницы: 2

Бренд: xFyre Страницы: 60

Бренд: A.O. Smith Страницы: 8

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 6

Бренд: A.O. Smith Страницы: 40

Бренд: Salamander Pumps Страницы: 24

Бренд: CLIVET Страницы: 7

Бренд: ProMinent Страницы: 81

Бренд: vacuubrand Страницы: 80

Бренд: DAB Страницы: 41

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды