ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 118 / 178

background image

NOTICE:

Ensure that the pipe threads are clean. Apply thread sealant to the plugs and fittings. Failure to
do so may result in oil leaks and equipment damage.

NOTICE:

There are several methods used to install bearings. The recommended method is to use an
induction heater that heats as well as demagnetizes the bearings. Failure to use this method
may result in equipment damage.

1.

Prepare the bearing frame (228) as follows (see the illustration):

a) Install the oil-fill plug (113A).

b) Install the oil-drain plug (408A).

c)

Install the sight glass (319).

d) Install the sight oiler plug (408J).

e) Install the plug for the oil-cooler inlet (408L).

f)

Install the plug for the oil-cooler outlet (408M).

g) Install four oil-mist connection plugs (408H).

Or: Install two grease fittings (193) and two grease-relief plugs (113).

h) Attach the bearing-frame foot (241) and fasten the bolts (370F) by hand.

370F

241

408A

408L

319

228A

408W

113A

372T

761B

408W

408M

408N

Figure 106: Attach the bearing-frame foot

2.

Install the oil flinger (248A) onto the shaft (122).

NOTICE:

The oil flinger is press fitted onto the shaft. Use a properly sized driver. Failure to do so may
result in damage to the oil flinger.

3.

Place the bearing-clamp ring (253B) onto the shaft (122).

Make sure that the orientation of the bearing-clamp ring is correct.

4.

Install outboard bearings (112A) on shaft (122).

6.6 Reassembly

116

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
116
117
118
119
120
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: Calpeda Страницы: 44

Бренд: Calpeda Страницы: 64

Бренд: Calpeda Страницы: 32

Бренд: Walrus Pump Страницы: 8

Бренд: Airetool Страницы: 20

Comfort 5000/5 LCD

Бренд: Gardena Страницы: 13

Бренд: DAB Страницы: 72

Бренд: Galletti Страницы: 60

Бренд: Alpine Страницы: 20

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренд: Bradford White Страницы: 21

Бренд: Wilo Страницы: 19

Бренд: Barmesa Pumps Страницы: 10

Бренд: Hubbell Страницы: 27

Бренд: Reliable Страницы: 18

Бренд: Ironton Страницы: 17

Бренд: Simer Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды