ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 117 / 178

background image

10. Prepare the shaft for assembly as follows (see the illustration):

a) Place the bearing-clamp ring (253B) onto the shaft (122).

b) Fasten the clamp-ring bolts (236A) crosswise.

See the specified torque values.

Make sure that the shaft rotates freely.

c)

Install a new O-ring (496).

d) Install the outboard labyrinth oil-seal (332A) into the bearing housing (134).

Place the drain slots of the oil seal at the bottom position (6 o’clock).

Make sure that the edges of the keyway are free from burrs. To protect the O-ring, cover the keyway
lengthwise with a piece of electrical tape before you install the oil seal.

236A

253B

134

332A

496

Figure 105: Outboard labyrinth oil seal reassembly

11. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.

b) Coat all the internal surfaces of the bearing frame (228) with oil.

c)

Install the shaft assembly into the bearing frame (228).

Make sure that the shaft rotates freely.

d) Install the clamp bolts (370C) in the bearing housing (134) and tighten by hand.

e) Install the jack bolts (370D) with the locknuts (423) in the bearing housing (134) and tighten by

hand.

6.6.3 Assemble the rotating element and the bearing frame (LTi)

WARNING:

Lifting and handling heavy equipment poses a crush hazard. Use caution during lifting and
handling and wear appropriate Personal Protective Equipment (PPE, such as steel-toed shoes,
gloves, etc.) at all times. Seek assistance if necessary.

CAUTION:

Risk of physical injury from hot bearings. Wear insulated gloves when using a bearing heater.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

115

«
...
115
116
117
118
119
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: salmson Страницы: 16

Бренд: Zoeller Страницы: 10

Бренд: Davey Страницы: 28

Бренд: WAGNER Страницы: 100

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 26

DURA-Power DRE-52

Бренд: A.O. Smith Страницы: 20

Бренд: A.O. Smith Страницы: 6

WILDEN P100 Advanced Plastic

Бренд: PSG Dover Страницы: 28

Бренд: Xylem Страницы: 44

Marvair AVPA 24

Бренд: Airxcel Страницы: 44

Бренд: Little Giant Страницы: 2

Бренд: Conel Страницы: 104

Бренд: Aqua MAX Страницы: 56

Бренд: Quantum Страницы: 36

Бренд: VAKI Страницы: 9

RoadLazer Husky 515

Бренд: Graco Страницы: 2

WSAN-XSC3 MF 200.4

Бренд: CLIVET Страницы: 68

Бренд: salmson Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды