ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя | Manualshive

Страница: 70 / 178

background image

•

Risk of equipment damage from unexpected heat generation. Do not overload the driver.
Ensure that the pump operating conditions are suitable for the driver. The driver can
overload in these circumstances:

•

The specific gravity or viscosity of the fluid is greater than expected

•

The pumped fluid exceeds the rated flow rate.

Operation at reduced capacity

WARNING:

•

Risk of breach of containment and equipment damage. Excessive vibration levels can
cause damage to bearings, stuffing box, seal chamber, and/or mechanical seal. Observe
pump for vibration levels, bearing temperature, and excessive noise. If normal levels are
exceeded, shut down and resolve.

•

Risk of explosion and serious physical injury. Do not operate pump with blocked system
piping or with suction or discharge valves closed. This can result in rapid heating and va-
porization of pumpage.

•

Risk of equipment damage and serious physical injury. Heat build-up can cause rotating
parts to score or seize. Observe pump for excessive heat build-up. If normal levels are
exceeded, shut down and resolve.

NOTICE:

Cavitation can cause damage to the internal surfaces of the pump. Ensure net positive suction
head available (NPSH

A

) always exceeds NPSH required (NPSH

3

) as shown on the published

performance curve of the pump.

Operation under freezing conditions

NOTICE:

Do not expose an idle pump to freezing conditions. Drain all liquid that will freeze that is inside
the pump and any auxiliary equipment. Failure to do so can cause liquid to freeze and damage
the pump. Note that different liquids freeze at different temperatures. Some pump designs do
not drain completely and may require flushing with a liquid that doesn't freeze.

5.14 Shut down the pump

WARNING:

Precautions must be taken to prevent physical injury. The pump may handle hazardous and/or
toxic fluids. Proper personal protective equipment should be worn. Pumpage must be handled
and disposed of in conformance with applicable environmental regulations.

1.

Slowly close the discharge valve.

2.

Shut down and lock out the driver to prevent accidental rotation.

5.14 Shut down the pump

68

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

«
...
68
69
70
71
72
...
»

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренд: Jacuzzi Страницы: 8

Sewers 1000 Series

Бренд: E-one Страницы: 3

Бренд: E-one Страницы: 23

Бренд: E-one Страницы: 76

Бренд: Zoeller Страницы: 8

Бренд: Kamar Страницы: 8

Pure Link 1300 Series

Бренд: lancer Страницы: 20

Tranquility Low-Profile Series

Бренд: ClimateMaster Страницы: 76

Бренд: Rinnai Страницы: 18

Бренд: Gardner Denver Страницы: 27

Бренд: EBARA Страницы: 20

Бренд: Graco Страницы: 20

Бренд: OSNA Страницы: 40

Бренд: Swim & Fun Страницы: 136

Бренд: Predator Страницы: 8

MAESTRO SMART 9HP

Бренд: Olimpia splendid Страницы: 52

Бренд: A.O. Smith Страницы: 74

Бренд: SPERONI Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды