ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 120 / 178

b) Coat the bore of the bearing housing (134) with oil.

Put the bearing housing (134) onto the shaft.

Do not use force.

134

Figure 109: Bearing housing reassembly

11. Prepare the shaft for assembly as follows (see the illustration):

a) Fasten the clamp-ring bolts (236A) crosswise.

See the specified torque values.

Make sure that the shaft rotates freely.

b) Install a new O-ring (496).

Install the outboard labyrinth oil-seal (332A) into the bearing housing (134).

Place the drain slots of the oil seal at the bottom position (6 o’clock).

Make sure that the edges of the keyway are free from burrs. To protect the O-ring, cover the keyway
lengthwise with a piece of electrical tape before you install the oil seal.

236A

253B

134

496

332A

Figure 110: Outboard labyrinth oil-seal reassembly

12. Install the shaft assembly into the bearing frame as follows (see the illustration):

a) Coat the outside of the bearing housing (134) with oil.

b) Coat all the internal surfaces of the bearing frame (228) with oil.

Install the shaft assembly into the bearing frame (228).

Make sure that the shaft rotates freely.

d) Install the clamp bolts (370C) in the bearing housing (134) and tighten by hand.

e) Install the jack bolts (370D) with the locknuts (423) in the bearing housing (134) and tighten by

hand.

6.6 Reassembly

118

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды