ITT Goulds Pumps CV 3196 i-FRAME Скачать руководство пользователя

Страница: 135 / 178

444

184

262

264

107

355

106

265

Figure 120: Backplate placement

Place the repeller (262) in the backplate (444) with the sleeve side up.

Place a PTFE gasket (264) on the backplate (444) and align the holes in the gasket with the holes
in the backplate.

Place a stuffing-box cover (184) on the backplate (444) and align the holes in the gasket with the
holes in the backplate.

Install four socket-head capscrews (265) and tighten them securely.

Install a new sealing element into the gland.

Install a gasket (360Q) and gland (107) on the stuffing-box cover (184).

Install the nuts (355).

Install a dynamic-seal assembly and nuts (370H).

370H

Figure 121: Dynamic seal installation

10. Check the stuffing-box-cover runout and rotate the indicator through 360 degrees.

An indicator reading that is greater than 0.013 mm | 0.005 in. indicates a problem.

6.6 Reassembly

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

133

Содержание Goulds Pumps CV 3196 i-FRAME



















































































































































































Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды

ITT Goulds Pumps CV 3196 i-FRAME, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps CV 3196 i-FRAME

Отзывы:

Похожие инструкции для Goulds Pumps CV 3196 i-FRAME

Бренды по названию

Популярные бренды