SECTION 6: PREVENTATIVE MAINTENANCE
Part No. 715-0080, Rev. B
- 61 -
3.
Inspect tanks for abrasion, cuts, or other damage.
4.
The tanks should be replaced according to the manufacturer’s recommendation.
INFANT CHAMBER INSPECTION & CLEANING
1.
Carefully inspect the infant chamber for cracks and crazing of the Plexiglas.
2.
Check all screws and knobs for tightness.
CAUTION:
Do not overtighten the infant chamber screws!
3.
Wash chamber with mild soap or detergent and water solution to clean the Plexiglas.
Household ammonia in water in the concentrations recommended for hospital cleaning is
also excellent. These solutions may be applied with a soft absorbent cloth, followed by
rinsing with clean water. Wipe away residue with soft chamois or cellulose sponge
material.
CAUTION:
Any type of alcohol or solvents should never be used for cleaning the
infant chamber, as these solvents tend to soften the surface and often
cause crazing. Cleansing materials containing abrasives or strong
solvents as found in some window cleaning preparations should never
be used to clean the inner and outer infant chamber.
BATTERY TEST
The incubator is equipped with a 12 volt 26 ampere-hour battery. Under normal operating
conditions in an ambient temperature of 20
C, a new fully charged battery should operate the
incubator for over three hours. If the operating time is less than 1 ¼ hours, the battery needs to
be replaced.
The battery is specified for only a finite number of complete discharges. The test of the battery
will completely discharge it. The test can be performed as follows:
1.
Ensure the battery is fully charged by connecting the incubator to AC power for 12 hours
with the power switch off.
2.
Place the incubator in a room with a temperature of approximately 20 - 23
C. Turn on
the incubator power switch and adjust the setpoint on the front panel to 37
C. Let the
incubator stabilize to its operational temperature with AC power.
3.
After the incubator has reached operating temperature, allow an additional twenty
minutes for stabilization.
Содержание AirBORNE A750i
