Intergraph TDZ 2000 Скачать руководство пользователя страница 74

Страница: 74 / 98

ERROR - System hard disk drive not recognized.

Reason

Solution

Hard disk drive power cable not attached.

Open the case and ensure power cable is
properly attached. See System Reference.

Hard disk drive SCSI cable not attached.

Open the case. Ensure the SCSI cable is
properly attached at both ends. See System
Reference.

A SCSI address conflict exists between the
hard disk drive you installed and another
SCSI device.

Remove the hard disk drive and change
SCSI ID to an unused setting. See the
documentation shipped with the hard disk
drive.

SCSI termination is enabled on the hard
disk drive you installed.

Disable the SCSI termination. See the
documentation shipped with the hard disk
drive.

Some viruses cause the system to not
recognize hard disk drives.

Run a virus scan program that checks the
Master Boot Record. Clear any viruses
detected by the program.

ERROR - “Invalid configuration information for SLOT XX” message displays.

Reason

Solution

System is not properly configured to
recognize the new ISA option board.

Use the Chipset menu parameters in
AMIBIOS Setup to reserve system resources
for the board. See Chapter 4.

ERROR - Total amount of memory does not display.

Reason

Solution

Faulty DIMM(s).

Identify faulty DIMM(s) by swapping
DIMM(s) until the faulty one is found. See
System Reference.

DIMM(s) not properly seated into socket(s).

Ensure DIMM(s) are properly installed. See
System Reference.

ERROR - I/O card parity error message displays.

Reason

Solution

Faulty option board is installed in ISA slot.

Remove ISA board, then restart the system.
See System Reference.

Содержание TDZ 2000



































































































Результаты поиска

Содержание TDZ 2000

Отзывы:

Похожие инструкции для TDZ 2000

Бренды по названию

Популярные бренды

Intergraph TDZ 2000, Настройка системы

Результаты поиска

Содержание TDZ 2000

Отзывы:

Похожие инструкции для TDZ 2000

Бренды по названию

Популярные бренды