Intel 82562EX Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 68

background image

82540EP/82541(PI/GI/EI) & 82562EZ(EX) Dual Footprint Design Guide

21

4.0

Ethernet Component Layout Guidelines

These sections provide recommendations for performing printed circuit board layouts. Good layout
practices are essential to meet IEEE PHY conformance specifications and EMI regulatory
requirements.

4.1

General Layout Considerations for Ethernet Controllers

Critical signal traces should be kept as short as possible to decrease the likelihood of being affected
by high frequency noise from other signals, including noise carried on power and ground planes.
Keeping the traces as short as possible can also reduce capacitive loading.

Since the transmission line medium extends onto the printed circuit board, special attention must
be paid to layout and routing of the differential signal pairs.

Designing for Gigabit operation is very similar to designing for 10/100 Mbps. For the 82541xx
Gigabit Ethernet Controller, system level tests should be performed at all three speeds.

4.1.1

Guidelines for Component Placement

Component placement can affect signal quality, emissions, and component operating temperature.
This section provides guidelines for component placement. Careful component placement can:

•

Decrease potential problems directly related to Electromagnetic Interference (EMI), which
could cause failure to meet applicable government test specifications.

•

Simplify the task of routing traces. To some extent, component orientation will affect the
complexity of trace routing. The overall objective is to minimize turns and crossovers between
traces.

Minimizing the amount of required space for the Ethernet LAN interface is important because
other interfaces will compete for physical space on a motherboard near the connector. The Ethernet
LAN circuits need to be as close as possible to the connector (see

«
...
27
28
29
30
31
...
»

Содержание 82562EX





































































Отзывы:

Нет отзывов

Похожие инструкции для 82562EX

Бренд: Zenith Data Systems Страницы: 64

Бренд: Delta Tau Страницы: 74

Supero SAS-826A

Бренд: Supero Страницы: 16

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренд: XJTAG Страницы: 9

Бренд: Xilinx Страницы: 8

Бренд: Crystal Vision Страницы: 54

Бренд: Intel Страницы: 20

Бренд: RAK Страницы: 14

Бренд: National Instruments Страницы: 45

Бренд: Inter-m Страницы: 20

Бренд: Forcepoint Страницы: 2

Бренд: Allied Telesis Страницы: 44

MultiModem ISIHP-2S

Бренд: Multitech Страницы: 155

USB device 622x

Бренд: National Instruments Страницы: 23

Бренд: Spectrum Digital Страницы: 11

Бренд: ICP DAS USA Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды