INIM smartliving series, Руководство пользователя

Страница: 60 / 64

60 Technical terminology and Glossary
Centrali anti-intrusione
This device allows users to access and control the system. The system readers are connected to the
control panel via the I-BUS.
The readers allows users to arm/disarm the partitions which are common to both the reader and key
in use (refer to Shortcuts). The key (TAG) must be held in the vicinity of the reader in such a way to
allow the system to read it and permit access to authorized operations. Although readers provide a
more limited access to the system, they are easiest way of carrying out day-to-day operations (arm,
disarm, etc.).
READER
A pre-set arming configuration which applies various operating modes to the system partitions.
SCENARIO
The shortcuts are control panel functions which, in a single activation, provide a fast way of carrying
out specific operations which would normally require a series of activations.
They can be activated by the end-user (at keypads, on codes typed in at keypads or on remote
telephones, at readers or on keys) or on the occurrence (activation) of an event.
SHORTCUTS
Optical smoke detectors are equipped with sampling chambers (based on light scattering mass -
Tyndall effect). They are capable of sensing the presence of smoke particles and thus detecting a fire
in its early stages.
These detectors have low power absorption during standby. The current absorption increases during
alarm status and thus signals the danger of fire to the control panel.
SMOKE DETECTORS
The “supervision time” is the interval during which the wireless-system devices (in general wireless
detectors in permanent placements) must signal to the control panel that they are operating in the
network. If a wireless device fails to signal before the “supervision time” expires, it will be classified as
“Lost” and the control panel will trigger a “peripheral-loss” fault event.
SUPERVISION
Detection of a serious condition that jeopardizes the operating capacity of the device concerned and
thus puts the system at risk.
Tamper conditions are detected by tamper switches connected to the system zones, keypads, readers,
expansions and control panel. Generally, these events are triggered by system violation such as
unauthorized opening of a keypad cover.
TAMPER
These are calls sent to programmed contact numbers when specific events start and end (restoral).
TELEPHONE ACTIONS
This is a service provided by the installer company with the user's collaboration. The installer connects
to the control panel over-the-phone or via a GPRS or Internet connection and, in this way, can check
and/or change the control panel programming data.
TELESERVICE
A zone with this attribute cannot generate alarms (activate audible and visual signalling devices).
However, any alarm events which occur will be saved to the events memory.
If zones are not operating properly, the “Test” option will allow the installer to check them without the
risk of generating false alarms
TEST ZONE
A logical entity for automatic time-management of programmed peripherals or elements.
SmartLiving control panels provide 10 timers.
TIMER
Transceiver-equipped devices
In two-way wireless systems, all the devices are equipped with transceivers. In one-way wireless
systems, the main unit is equipped with a receiver module whereas the peripheral devices are
equipped with transmitters.
TRANSCEIVER
Each code is programmed with:
• A 4, 5 or 6 digit PIN which allows access the system.
• A label which identifies the user (usually the user's name).
• The group of partitions it controls (arms, disarms, etc.).
• A group of pre-set parameters which allow the operator to work on the system in accordance with
its authorized access level (for example, a code can be enabled to consult the events log but not to
change the date and time).
• A hierarchical level, that may allow the user to change to parameters of codes on a lower level in
the system hierarchy.
- User (the lowest level)
- Manager
- Master
USER CODE
List of functions available to the user after entry of a valid code at the keypad.
USER MENU
This device allows the control panel to send voice calls to programmed contact numbers.
In SmartLiving control panels the voice dialler function is provided by the SmartLogos30M board
(accessory item).
VOICE DIALER
If the system is equipped with a SmartLogos30M voice board, all keypads with voice functions present
in the system configuration will allow users to record memos. Messages can be recorded, played and
deleted as required.
VOICE MEMO
Software application that allows you to view web contents over the Internet.
WEB BROWSER
Software application that processes web page requests from a web browser.
The SmartLAN/G network board has an integrated web server that provides the browser with a web
interface for the management and supervision of the SmartLiving system.
WEB SERVER
An intrusion control system whose devices (detectors, keypads, keyfobs) communicate with the
control panel over radio waves.
Usually, only the control panel of wireless-systems is mains powered (220Va.c.) while, the wireless
devices are battery powered. The battery life is of utmost importance in the design layout and
operational capacity of these systems.
WIRELESS
An electrical input point used for the management/supervision of signals coming from an intrusion
detection device.
ZONE