ifm
Device manual AS-i M4 Gateway Profibus DPV1 (AC1375, AC1376)
2012-02-23
Index
521
Module 12, extended command 97 (61hex) – make
settings in the AS-i master............................................... 304
Module 2 – Binary inputs/outputs of single/A slaves
of AS-i master 2............................................................... 158
Module 3 – Binary inputs/outputs of B slaves of
AS-i master 1................................................................... 159
Module 4 – Binary inputs/outputs of B slaves of
AS-i master 2................................................................... 160
Module 5 – Multiplexed analogue inputs of
AS-i masters 1/2 .............................................................. 161
Module 6 – Multiplexed analogue outputs of
AS-i masters 1/2 .............................................................. 162
Module 7 – Command channel ............................................. 163
Module 7, command 01 – Read master flags........................ 173
Module 7, command 02 – Change operating mode .............. 174
Module 7, command 03 – Read current slave
configuration .................................................................... 175
Module 7, command 04 – Read projected slave
configuration .................................................................... 177
Module 7, command 05 – Change projected slave
configuration .................................................................... 179
Module 7, command 06 – Read slave parameters ............... 181
Module 7, command 07 – Change projected slave
parameters....................................................................... 182
Module 7, command 08 – Read LAS (list of active slaves)... 184
Module 7, command 09 – Read LDS (list of detected
slaves) ............................................................................. 186
Module 7, Command 10 (0Ahex) – Read LPF (list of
slaves with peripheral fault) ............................................. 188
Module 7, command 11 (0Bhex) – Read LPS (list of
projected slaves).............................................................. 190
Module 7, command 13 (0Dhex) – Read telegram
error counter .................................................................... 192
Module 7, command 14 (0Ehex) – Read configuration
error counter .................................................................... 194
Module 7, command 15 (0Fhex) – Read AS-i cycle
counter............................................................................. 195
Module 7, command 16 (10hex) – Change current
slave parameters ............................................................. 196
Module 7, command 19 (13hex) – Project all........................ 198
Module 7, command 21 (15hex) – Save configuration
in flash memory ............................................................... 199
Module 7, command 22 (16hex) – Reset telegram
error counter of a slave.................................................... 200
Module 7, command 23 (17hex) – Address slave................. 202
Module 7, command 62 (3Ehex) – [Continuous Command]
operating mode................................................................ 204
Module 7, command 63 (3Fhex) – No-operation command
without function................................................................ 206
Module 8 – Data transmission between Profibus DP master
and PLC in the ControllerE.............................................. 166
Module 9 – Data transmission between PLC in the
ControllerE and the Profibus DP master ......................... 166
MRAM.................................................................................... 513
MSB....................................................................................... 513
Number of AS-i voltage failures on the AS-i master.............. 427
Number of configuration errors on the master....................... 429
Number of disturbed telegrams on the master (by
noisy slaves).................................................................... 434
On this manual .......................................................................... 9
Operating and display elements.............................................. 92
Operating system .................................................................. 513
Operation............................................................................... 413
OSC....................................................................................... 513
OSSD .................................................................................... 513
Overview
Where is what for AC1375?...........................................................13
Where is what for AC1376?...........................................................14
Overview of the commands in the DP module 7 ................... 164
Parameter setting of the Profibus host.................................. 145
Password............................................................................... 513
Password levels..................................................................... 137
Password protection.............................................................. 136
Password setting ................................................................... 138
PCCD..................................................................................... 513
PCD ....................................................................................... 513
PDM....................................................................................... 514
PELV...................................................................................... 514
Permissible slave addresses................................................. 120
Permitted use .......................................................................... 15
Pictogram .............................................................................. 514
PLC configuration.................................................................. 514
Polling.................................................................................... 514
Power-on delay time.............................................................. 514
Process image....................................................................... 514
Profibus ................................................................................. 514
Profiles of AS-i slaves.............................................................. 32
Profinet .................................................................................. 515
Programming software .......................................................... 146
Prohibited use.......................................................................... 15
Read fieldbus parameters ..................................................... 408
Read states of safety slaves ................................................. 445
Read states of the safety monitor.......................................... 441
Redundant ............................................................................. 515
Remanent .............................................................................. 515
Required accessories.............................................................. 14
Reset AS-i address of the safety monitor.............................. 452
Reset diagnostic states of safety devices ............................. 458
Reset error counter................................................................ 437
Reset to factory preset .......................................................... 140
RTC ....................................................................................... 515
RTS........................................................................................ 515
RTS errors – error codes R01...R43 ..................................... 494
Safety instructions ................................................................... 11
SD card.................................................................................. 516
Self-test ................................................................................. 516
SELV...................................................................................... 516
Services for acyclic data transfer between DPM1 master
and slave ......................................................................... 315
Services for acyclic data transfer between DPM2 master
and slave ......................................................................... 315
Set analogue output .............................................................. 471
Set AS-i address of the safety monitor.................................. 449
Set digital output.................................................................... 469
Set output values................................................................... 466
Set the diagnostic characteristics of the safety monitor ........ 455
Set the parameters of the fieldbus interface in the device .... 143
Set the Profibus slave address on the gateway .................... 406
Set-up .................................................................................... 119
Single slave ........................................................................... 516
Slave...................................................................................... 516
Slave configuration................................................................ 516
Slave group in module 7........................................................ 185
Slave profiles for slaves with combined transaction................ 38
Status information of analogue slaves .................................. 465
strAnalogSlave – fields with analogue I/O data....................... 25
strFbusInCyc / strFbusOutCyc – fields with fieldbus I/O data . 20
strMasterFlags – fields with master status information ........... 18
strSafetyList – fields with safety slave contacts ...................... 31
strSlaveCDI / strSlavePrj – fields with current and projected
configuration data (CDI) ..................................................... 22
