IEI Technology KINO-LX Скачать руководство пользователя

Страница: 93 / 197

Page 93

KINO-LX Motherboard

The following menu options are seen in

BIOS Menu 1

Standard CMOS Features

: Changes the basic system configuration.

Advanced BIOS Features

: Changes the advanced system settings.

Advanced Chipset Features

: Changes the chipset configuration features.

Integrated Peripherals

: Changes the settings for integrated peripherals.

Power Management Setup

: Configures power saving options.

PnP/PCI Configurations

: Changes the advanced PCI/PnP settings.

PC Health Status

: Monitors essential system parameters.

The following user configurable options are also available in

BIOS Menu 1

Load Fail-Safe Defaults

Select this option to load failsafe default values for each BIOS parameter in the setup

menus. Press

for this operation on any page.

Load Optimized Defaults

Select this option to load optimal default values for each BIOS parameter in the setup

menus. Press

for this operation on any page.

Set Supervisor Password

By default, no supervisor password is set. To install a supervisor password, select this

field and enter the password. After this option is selected, a red dialogue box appears with

“

Enter Password:

”. Type the password and press

NTER

. Retype the original password

into the “

Confirm Password:

” dialogue box and press

NTER

. To disable the password,

simply press

NTER

in the “

Enter Password:

” dialogue box, then press any key in the

“

Password Disabled !!!

” dialogue box.

Set User Password

By default no user password is set. To install a user password, select this field and enter

the password. After this option is selected, a red dialogue box appears with “

Enter

Password:

”. Type the password and press

NTER

. Retype the original password into the

“

Confirm Password:

” dialogue box and press

NTER

. To disable the password, simply

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

Похожие инструкции для KINO-LX

Бренды по названию

Популярные бренды

IEI Technology KINO-LX, Руководство пользователя

Результаты поиска

Содержание KINO-LX

Отзывы:

Похожие инструкции для KINO-LX

Бренды по названию

Популярные бренды