IEI Technology KINO-LX Скачать руководство пользователя страница 114

Страница: 114 / 197

Page 114

IEI® Technology, Corp

KINO-LX Motherboard

Mode 0

PIO mode 0 selected with a maximum transfer rate of 3.3MBps.

Mode 1

PIO mode 1 selected with a maximum transfer rate of 5.2MBps.

Mode 2

PIO mode 2 selected with a maximum transfer rate of 8.3MBps.

Mode 3

PIO mode 3 selected with a maximum transfer rate of 11.1MBps.

Mode 4

PIO mode 4 selected with a maximum transfer rate of 16.6MBps.

IDE UDMA [Auto]

Use the

IDE UDMA

option below to select the Ultra DMA (UDMA) mode for the following

HDDs:

IDE Primary Master UDMA

IDE Primary Slave UDMA

Auto

(Default)

The computer selects the correct UDMA.

Disabled

The UDMA for the HDD device is disabled.

IDE DMA transfer access [Enabled]

Use the

IDE DMA transfer access

option to enable or disable DMA support for IDE

devices connected to the system.

Disabled

All IDE drive DMA transfers are disabled. The IDE drives

use PIO mode transfers.

Enabled

(Default)

All IDE drive DMA transfers are enabled.

IDE HDD Block Mode [Enabled]

If the drive connected to the system supports block mode, use the

IDE HDD Block Mode

option to enable the system to detect the optimal number of block read/writes per sector

the system IDE drive can support. Block mode is also called block transfer, multiple

commands, or multiple sector read/write.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 114 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: