IEI Technology KINO-LX Скачать руководство пользователя страница 88

Страница: 88 / 197

Page 88

IEI® Technology, Corp

KINO-LX Motherboard

4.8.2 Serial Connection

The external peripheral interface connector panel serial connector provides easy and

quick access to external serial devices.

4.8.3 Parallel Connector

The external parallel port connector connects to a printer. The parallel port interface can

be re-assigned to LPT2 or LPT3 through the BIOS configuration utility. The default

interrupt channel is IRQ7. Select ECP or EPP DMA mode using the BIOS configuration

utility.

4.8.4 LCD Panel Connection

The conventional CRT monitor connector is a 15-pin, female D-SUB connector. It can be

connected to an external monitor.

4.8.5 Ethernet Connection

The rear panel RJ-45 connectors can be connected to an external LAN and communicate

with data transfer rates up to 10Mbps and 100Mbps.

4.8.6 USB Connection

The rear panel USB connectors provide easier and quicker access to external USB

devices. The rear panel USB connector is a standard connector and can easily be

connected to other USB devices.

4.8.7 Audio Interface

AC’97 Audio signals are interfaced through two phone jack connections. The red phone

jack is for Mic In and green is for Speaker Out.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 88 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: