IEI Technology KINO-LX Скачать руководство пользователя страница 101

Страница: 101 / 197

Page 101

KINO-LX Motherboard

Enabled

Activates automatically when the system boots up

causing a warning message to appear when anything

attempts to access the boot sector or HDD partition table.

Disabled

(Default)

No warning message appears when there is an attempt

to access the boot sector or HDD partition table.

CPU Internal Cache [Enabled]

Use the

CPU Internal Cache

option to enable or disable the internal CPU cache.

Disabled

The internal CPU cache is disabled.

Enabled

(Default)

The internal CPU cache is enabled.

Boot From LAN Control [Disabled]

Use the

BOOT From LAN Control

option to enable the system to be booted from a

remote system.

Disabled

(Default)

The system cannot be booted from a remote system

through the LAN.

Enabled

The system can be booted from a remote system

through the LAN.

SATA Boot ROM Control [Disabled]

Use the

SATA Boot ROM Control

option to configure SATA IDE use in DOS mode.

Disabled

(Default)

Disables SATA IDE use in DOS mode.

Enabled

Enables SATA IDE use in DOS mode.

Boot Device

Use the

Boot Device

options to select the order of the devices the system boots from.

There are three boot device configuration options:

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 101 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: