IEI Technology KINO-LX Скачать руководство пользователя страница 106

Страница: 106 / 197

Page 106

IEI® Technology, Corp

KINO-LX Motherboard

OS Select For DRAM > 64MB [Non-OS2]

Use the

OS Select For DRAM > 64MB

option to specify the operating system.

Enabled

Specifies the operating system used as OS/2.

Disabled

(Default)

Select this option when not using the OS/2 operating

system.

Delay for HDD (Secs) [3]

Use the

Delay for HDD

option to specify the period of time the system should wait before

the HDD is identified. If selected, the user is asked to enter a number between 0 and 15.

The number specified is the number of seconds the system waits before the HDD is

identified.

Small Logo (EPA) Show [Disabled]

Use the

Small Logo (EPA) Show

option to specify if the Environmental Protection

Agency (EPA) logo appears during the system boot-up process. If enabled, the boot up

process may be delayed.

Disabled

(Default)

EPA logo does not appear during boot up.

Enabled

EPA logo appears during boot up.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 106 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: