IEI Technology KINO-LX Скачать руководство пользователя страница 80

Страница: 80 / 197

Page 80

IEI® Technology, Corp

KINO-LX Motherboard

NOTE:

When two EIDE disk drives are connected together, back-end jumpers on

the drives must be used to configure one drive as a master and the other as

a slave.

4.5.2 COM3-COM6 RS-232 Serial Port Installation

The cable used to connect the motherboard to an RS-232 serial port is a 10-pin header to

male D-sub 9 connector. To connect an RS-232 serial port to the motherboard, follow the

instructions below.

Step 1:

Step 2:

Step 3:

Step 1:

Find the RS-232 cable in the kit that came with the motherboard.

Connect the 10-pin connector end of the cables to the COM3 to COM6 box

headers on the motherboard. Be sure to align the red wire on the connector to

pin 1 on the box header.

Connect the other end of the cables to standard female D-sub 9 connectors.

Step 0:

4.5.3 COM2 RS-232/485 Serial Port Installation

To connect an RS-232/485 serial port to the motherboard, follow the instructions below.

Connect the 14-pin connector end of an RS-422/485 serial port cable to the

CN10 connector on the motherboard.

Step 0:

NOTE:

Be sure to configure the JP2 COM2 RS232/RS485 Select Jumper for either an

RS-232 or RS-485 connection. Refer to

Section

4.5

for more information.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 80 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: