IEI Technology KINO-LX Скачать руководство пользователя страница 70

Страница: 70 / 197

Page 70

IEI® Technology, Corp

KINO-LX Motherboard

3.3.5 LAN Connectors

CN Label:

CN6

and

CN7

CN Type:

RJ-45

CN Location:

See

Figure 3-18

(labeled number 5 and 6)

CN Pinouts:

See

Table 3-24

The KINO-LX is equipped with two built-in GbE Ethernet controllers. The controllers can

connect to the LAN through two RJ-45 LAN connectors. There are two LEDs on the

connector indicating the status of LAN. The pin assignments are listed in the following

table:

PIN DESCRIPTION PIN DESCRIPTION

1 +2.5VCC

2 TX0+

3 TX0-

4 TX1+

5 TX1-

6 TX2+

7 TX2-

8 TX3+

9 TX3-

GND

11 LINK-

12 LINK+

13 ACTIVE-

Table 3-24: LAN Pinouts

Figure 3-23: RJ-45Ethernet Connector

The RJ-45 Ethernet connector has two status LEDs, one green and one yellow

(

Figure 3-23

). The green LED indicates activity on the port and the yellow LED

indicates the port is linked. See

Table 3-25

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 70 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: