IEI Technology KINO-LX Скачать руководство пользователя страница 120

Страница: 120 / 197

Page 120

IEI® Technology, Corp

KINO-LX Motherboard

Power Management [ACPI]

Use the

Power Management

option to set the power management type used by the

system.

Disabled

All power management options are turned off. The only

user configurable options are the power button and

alarm settings.

Legacy

Standby and suspend modes can be set.

APM

Advanced power management (APM) is activated

ACPI

(Default) Advanced

Configuration

and Power Interface (ACPI) is

activated.

x Standby Mode [Disabled]

The

Standby Mode

option can only be selected if the

Power Management

option is set

Legacy

. The

Standby Mode

specifies the amount of time the system can be inactive

before the system enters standby mode. The

Standby Mode

options are:

Disabled (Default)

1 Sec

5 Sec

10 Sec

15 Sec

30 Sec

45 Sec

1 Min

5 Min

10 Min

15 Min

30 Min

45 Min

60 Min

90 Min

120 Min

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 120 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: