Icom AP-90M Скачать руководство пользователя страница 93

Страница: 93 / 103

MAINTENANCE

6-19

When the “Write USB Authentication Key” window is displayed, click [Next].

• To cancel the entry, click [Close].

When “The authentication key has been written to the USB flash drive.” is displayed, click [Close].

If you have inserted a flash drive in which an authentication key is already
saved, “An authentication key already exists on the USB flash drive. If you want
to overwrite the key, click the “Next” button.” is displayed.

Management > Management Tools



Entering the USB authentication key (Continued)

Turn OFF the AP-90M and remove the USB flash
drive.

NOTE:

To make sure the data is secure, turn the AP-90M
OFF before removing the USB flash drive.

AP-90M

WIRELESS A

CCESS POINT

Remove the USB flash drive

Power OFF

Click

8. Setting the USB Authentication Key

Содержание AP-90M








































































































Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды

Icom AP-90M, Инструкция по эксплуатации

Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды