manualshive.com logo in svg

Icom AP-90M, Инструкция по эксплуатации

Поделиться
Скачать
Icom AP-90M Скачать руководство пользователя страница 6

v

INTRODUCTION

Form2001

Menu

Setting screen

Setting

Title

Default setting

Network Settings

IP Address 

IP Address

IP Address

192.168.0.1

Subnet Mask

255.255.255.0

DHCP Server

DHCP Server

DHCP Server

Disable

Wireless Settings Wireless LAN

Wireless LAN

Frequency Band

2.4 GHz (Wireless 1)

*

5 GHz (Wireless 2)

*

Bandwidth

20 MHz

Virtual AP

Virtual AP

Interface

ath0 (Wireless 1)
ath4 (Wireless 2)

SSID

WIRELESSLAN-0

Security

Authentication

Open System/Shared Key

Encryption

None

Management

Administrator

Administrator Password

Username

admin (Cannot be changed)

Current Password

admin (Lower case letters)

*The wireless LAN unit for Wireless 1 (internal antenna) and Wireless 2 (external antenna).
 Wireless 1 and 2’s frequency bands cannot be used when both of them are set to 2.4 GHz or 5 GHz.
 The “IEEE802.11ac” standard can only be used when 5 GHz is selected in Wireless 2 (external antenna).

To prevent unauthorized access

You must carefully chose your password, and change it occasionally.

• Choose one that is not easy to guess.
• Use numbers, characters and letters (both lower and upper case).

 About default settings

Содержание AP-90M








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды