Icom AP-90M Скачать руководство пользователя страница 86

Страница: 86 / 103

MAINTENANCE

6-12

(

Continued on the next page)



Managing multiple setting files on one USB flash drive

To restore settings or to update the firmware using a USB flash drive:
a. You must have a folder created with the LAN MAC address as it’s name. (

p.6-6)

b. The folder must be displayed on the “TOP” screen.
c. The setting file and firmware file must be saved in the folder..

5. Automatic setting using a USB flash drive (Continued)

When there is no folder in the root directory

When there is a matching MAC address folder (Example: 0090C7000001)

When there is no matching MAC address folder (Example: 0090C7000002)

Reads the setting file or firmware file saved
in the root directory because there is no
matching MAC address found.

Reads the setting file or firmware file saved in
the previously created folder.

A setting backup file is created on the USB
flash drive’s root directory because there is no
matching MAC address found.

Setting backup file is created in the USB flash
drive’s root directory because there is no
matching MAC address found.

Creates a setting backup file on the previously
created folder.

Содержание AP-90M








































































































Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды

Icom AP-90M, Инструкция по эксплуатации

Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды