Procedure
1.
Remove the chassis door.
2.
Check the blade power and status LEDs and port status LEDs on the front of
each blade to identify any possible problems.
3.
Before replacing a blade, establish a Telnet or console connection to determine
a failure and verify operation after replacement. Use the
switchShow
and
slotShow
commands to view the status of the blades.
4.
Check for adequate cable slack. Ensure there is plenty of cable slack to remove
a blade without cable obstruction.
5.
Ensure that the part number on the unit being replaced matches the
replacement part number. The
chassisShow
command displays information
about the blades, including part numbers (xx-xxxxxxx-xx), serial numbers, and
additional status.
6.
Ensure that traffic is not flowing through the blade (port status LED should be
off) prior to disconnecting cables.
7.
Disconnect all cables and remove transceivers from the blade.
8.
If removing an extension blade, perform the following steps:
a.
Delete all fciptunnel configurations using the
portcfg fciptunnel
slot/vePort delete
command.
b.
Delete all IP Routes defined on the blade to be removed using the
portcfg
iproute delete
command.
c.
Delete all IP interfaces (IPIFs) defined on the blade using the
portcfg ipif
slot/geX delete
command.
d.
If logical switches are used on the switch, move all blade ports back to the
default logical switch. Refer to the
lscfg
command in the Fabric OS
Command Reference for details.
Note:
If you are removing the extension blade to install in a different slot, you
must remove configuration using the preceding steps, then reconfigure the
blade in the new slot. If you move the blade without performing these steps
and the blade faults, you must move the blade to the original slot and remove
configuration.
9.
Loosen the captive screws for both ejector handles on the blade using a #1
Phillips screwdriver. Loosening the screws initiates a hot-swap request and
disconnects power from the blade. The spring-loaded captive screws will pop
out from the slot .63 cm (.25 in.) when fully disengaged. Do not eject the blade
using blade handles until screws disengage from slot and the power LED is
off.
10.
Grasp both ejector handles and simultaneously pull them away from the
center of the blade using equal pressure to approximately 45 degrees (fully
open). As you move the handles, you will hear connectors disengaging from
the backplane connector and possibly a slight popping noise. This is normal
and is due to the dense backplane. The blade will move out approximately
1.27 cm (.5 in.) from the slot when fully disengaged.
11.
Pull the blade out from the slot slightly using the ejector handles until you can
grasp the blade edges with your hands. Make sure that the blade has cooled
sufficiently to touch.
CAUTION:
To avoid damaging blade and chassis, do not push the blade into a slot or
pull the blade from a slot using the ejector handles.
12.
Continue pulling the blade from the slot by the blade edges. As you slide out
the blade, place one hand under it for support. Do not support the blade by
112
SAN512B-6 Installation, Service, and User Guide
Содержание SAN512B-6
