IBM 8832L1X Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 154

background image

21

Removing the blade server bezel assembly

To install certain options, you must first remove the blade server bezel assembly. The following
illustration shows how to remove the bezel assembly from the blade server.

Complete the following steps to remove the blade server bezel assembly:

1. Read the safety information beginning on page vii and “Installation guidelines” on page 17.

2. Open the blade server cover (see “Opening the blade server cover” on page 20 for instructions).

3. Press the bezel-assembly release and pull the bezel assembly away from the blade server

approximately 1.2 cm (0.5 inch).

4. Disconnect the control-panel cable from the control-panel connector.

5. Pull the bezel assembly away from the blade server.

6. Store the bezel assembly in a safe place.

Installing a SCSI hard disk drive

The blade server has two connectors on the system board for installing optional Ultra320 SCSI hard
disk drives.

Each Ultra320 SCSI connector is on the same bus. Depending on your blade server, at least one
SCSI hard disk drive might already be installed. If your blade server is equipped with one SCSI hard
disk drive, you can install an additional SCSI hard disk drive. These two SCSI hard disk drives can
be used to implement and manage a redundant array of independent disks (RAID) level-1. See
“Configuring a SCSI RAID array” on page 59 for information about SCSI RAID configuration.

Attention: To maintain proper system cooling, do not operate the system unit without a blade
server, expansion unit, or filler blade installed in each blade bay.

The following illustration shows how to install a SCSI hard disk drive and tray in the blade server.

Control panel
connector

Bezel-assembly
release

Bezel-assembly
release

Control-panel
cable

«
...
35
36
37
38
39
...
»

Содержание 8832L1X



























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8832L1X

Бренд: F5 Страницы: 72

Бренд: SEH Страницы: 20

Adaptive Server IQ 12.4.2

Бренд: Sybase Страницы: 536

Бренд: Hi-flying Страницы: 29

Бренд: Hawking Страницы: 40

Бренд: Synology Страницы: 24

Бренд: Muton Страницы: 30

Бренд: Generac Power Systems Страницы: 52

Бренд: EVS Страницы: 126

Бренд: Super Страницы: 60

LANTIME M600 MRS

Бренд: Meinberg Страницы: 160

Бренд: Webster Страницы: 114

Бренд: GIGA-BYTE TECHNOLOGY Страницы: 84

Бренд: Lantronix Страницы: 30

PS 4000 Gen2 Series

Бренд: PAC STORAGE Страницы: 108

PowerEdge R740xd

Бренд: Dell EMC Страницы: 215

SuperBlade SBS-820H-420P

Бренд: Supermicro Страницы: 128

DiskStation DS213

Бренд: Synology Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды