IBM 7378 Скачать руководство пользователя страница 270

Страница: 270 / 362

Installing the USB cable and light path diagnostics assembly

To install the USB cable and light path diagnostics assembly, complete the following
steps:

1. Touch the static-protective package that contains the USB cable and light path

diagnostics assembly to any unpainted metal surface on the server; then,
remove the assembly from the package.

2. Connect the USB cable to the replacement USB cable and light path

diagnostics assembly:

a. Rotate the USB cable and light path diagnostics assembly mounting

bracket so that you are looking at the rear of the bracket.

b. Squeeze the retaining clips on each side of the USB cable connector and

align the key on the cable connector with the notch on the mounting
bracket.

c. Insert the connector into the mounting bracket; then, release the retaining

clips.

3. Feed the light path diagnostics cable into the server through the opening in the

front of the server.

4. Position the bottom of the USB cable and light path diagnostics assembly

mounting bracket into the opening and rotate the top of the bracket toward the
server until it clicks into place.

5. Connect the light path diagnostics cable to the system board. See “System

board internal connectors” on page 15 and“Internal cable routing and
connectors” on page 164 to locate the USB and light path diagnostics
connectors on the system board.

6. Install the fan cage assembly (see “Installing the fan cage assembly” on page

244).

7. Install the air baffle (see “Installing the air baffle” on page 213).

8. Return the power-supply cage to its closed position (see “Closing the

power-supply cage” on page 156).

9. Install the hot-swap power supply or power supplies (see “Installing a hot-swap

power supply” on page 274).

10. Install the bezel (see “Installing the bezel” on page 242).

11. Install and lock the left-side cover (see “Installing the left-side cover” on page

181).

252

IBM System x3400 M3 Types 7378 and 7379: Problem Determination and Service Guide

Содержание 7378











































































































































































































































































































































































Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды

IBM 7378, Руководство по диагностике и обслуживанию

Результаты поиска

Содержание 7378

Отзывы:

Похожие инструкции для 7378

Бренды по названию

Популярные бренды